[LINKS]

How to hook up ice maker

How to hook up ice maker

How to hook up ice maker

It takes patience, but you can hook a water line up to your refrigerator on your own. Slide the compression nut over the male threads and tighten it on the adapter. Screw the provided screws to the mounting holes on the side of the freezer wall Image 2. Finally, drain the lines by opening a faucet. Shut the water off to the house. There are a few different types of valves that can be used. To install a needle valve or saddle valve, place the two clamps around the copper pipe and use a screwdriver to tighten the screws on each side to hold the valve in place. Use pliers to untwist the faucet supply line from the cold water supply valve. All of these materials are available at home centers and plumbing supply houses. You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes. Step 2 Drain the Water Line Now that the water line has been run to the refrigerator, it's time to do what's called the "tap-in" to the cold water line underneath the sink. Now the refrigerator is connected. Tighten the connections slightly if you see a leak. Once the water line is in place, use a screwdriver to puncture a hole in the paper cover on the back of the unit. Use a flathead screwdriver to remove the plugs from the holes. Attach the free end of the copper tubing to the valve. Coil the excess water line behind the refrigerator. A needle valve is hollow, which will actually pierce the pipe and tap-in quickly. Plug your refrigerator into the wall. Connect the line to the water line connector on the back of the refrigerator. You should have cold water very shortly. Insert the extension tube into the smaller hole on the back of the freezer wall Image 1. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink. Locate the nearest cold water line and determine its location compared to the location of the fridge. Step 7 insert extension tube on back of freezer wall installing ice maker Install the Icemaker With all the work done on the back side of the freezer it's time to install the icemaker unit itself. Be sure to put a gasket seal between the valve and the T-fitting. How to hook up ice maker



Feed the line down, and then up through the refrigerator hole. Be sure to put a gasket seal between the valve and the T-fitting. Drill a hole either through the cabinet wall separating the space under the sink and the refrigerator or in the basement ceiling up to the refrigerator. Find the opening in the back of the fridge to receive the copper tubing and screw it into place. Step 7 insert extension tube on back of freezer wall installing ice maker Install the Icemaker With all the work done on the back side of the freezer it's time to install the icemaker unit itself. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. Be sure to keep the spacing equal to prevent leaking. Family Handyman , Whirlpool ]. Here's how [sources: Attach one end of the copper tubing to the refrigerator's water pipe, using a nut and ferrule. Insert the extension tube into the smaller hole on the back of the freezer wall Image 1. Begin installing the fill tube by placing the provided metal insert into the end of the water supply line Image 2. Step 4 mount the solenoid valve Mount the Solenoid Valve The first part of the icemaker kit is called the solenoid valve. Use the feeler bit to determine the best location to drill for the water line. Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position. Clean that area with the abrasive cloth and cut it with a pipe cutter. Screw the provided screws to the mounting holes on the side of the freezer wall Image 2. Place the end of the water line you intend to connect to the refrigerator into a 5-gallon bucket. Plug your refrigerator into the wall. Push the refrigerator against the wall. Watch for leaks at all the connections. Locate the cold water source closest to the refrigerator. Attach the fill tube to the freezer by sliding the angled part of the tube into the inlet hole in the back of the freezer and screw it into place. Let 1 or 2 gallons of water run through the new line to remove the air. Slide the provided water valve clamp over the fill tube, insert the water supply line and use a drill with a hex head bit to tighten everything up. Step 8 Mount the Unit to the Freezer Wall Mount the unit to the freezer wall by hanging the icemaker over the mounted screws; making sure to line up the extension tube into the reservoir. Turn off the supply line. To get power to the icemaker, plug in the wiring harness on the side of the ice maker unit into the wiring harness on the back of the freezer wall. For a DIYer, if codes allow -- a needle valve is recommended. Turn the cold water on the supply line clockwise to close it.

How to hook up ice maker



You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. Go back to the fridge and uncoil the rest of the copper tubing. All of these materials are available at home centers and plumbing supply houses. To tap into the line, shut off the water to the house at the main. Step 6 installing the fill tube Install the Factory Fill Tube The next step is to install the factory fill tube. Attach the fill tube to the freezer by sliding the angled part of the tube into the inlet hole in the back of the freezer and screw it into place. Screw the provided screws to the mounting holes on the side of the freezer wall Image 2. Turn off the supply line. Locate the nearest cold water line and determine its location compared to the location of the fridge. Now move to the back and install the fill tube. Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. Watch for leaks at all the connections. Be sure to keep the spacing equal to prevent leaking. Leave the excess water line behind the refrigerator. You should have cold water very shortly. Leave extra slack high on the fridge so that it can still be easily moved in and out. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet. Find the opening in the back of the fridge to receive the copper tubing and screw it into place. Clamp any tubing inside the cabinets along the back of the cabinets, to keep it in place. Tighten the connections slightly if you see a leak. Clean that area with the abrasive cloth and cut it with a pipe cutter. Use the feeler bit to determine the best location to drill for the water line. Attach the free end of the copper tubing to the valve. Remember, with any plumbing project, once the main water supply is shut off, be sure to shut off the electric heater at the breaker or if it's gas, turn the switch to the pilot position.



































How to hook up ice maker



Drill the hole. A needle valve is hollow, which will actually pierce the pipe and tap-in quickly. Use the feeler bit to determine the best location to drill for the water line. Find your water supply lines beneath your sink. Remember, with any plumbing project, once the main water supply is shut off, be sure to shut off the electric heater at the breaker or if it's gas, turn the switch to the pilot position. Thread the ferrule from the kit onto the new line. Attach the fill tube to the freezer by sliding the angled part of the tube into the inlet hole in the back of the freezer and screw it into place. Have a bucket ready to catch any water that comes out. You will have to wait hours before you have ice. Use a flathead screwdriver to remove the plugs from the holes. Use pliers to untwist the faucet supply line from the cold water supply valve. You may have three water supply lines beneath the sink; two lines connect directly to the faucet while the third line connects to the dishwasher. Put the fridge back in the opening and turn the water back on. Finally, drain the lines by opening a faucet. Connect the line to the water line connector on the back of the refrigerator. The valve connected to the right side of the faucet is the cold water supply line. Here's how [sources: The kit provides you with the required parts to hook up a water line to your refrigerator. Shut off the water supply. Attach a water valve to the T-fitting. Screw the provided screws to the mounting holes on the side of the freezer wall Image 2. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes. Locate the 2-pin solenoid connector usually found tucked or taped under the refrigerator and insert the connector over the valve solenoid terminals as far as possible. Family Handyman , Whirlpool ]. Be sure to put a gasket seal between the valve and the T-fitting.

Shut off the water supply. With that in mind, pull out the fridge and drill down with a feeler bit as close to the cold water line as possible. Wrap threads on the cold water valve with two or three wraps of thread-seal tape. Go down into the crawl space. Twist the faucet supply line onto the female end of the adapter. Now the refrigerator is connected. Step 8 Mount the Unit to the Freezer Wall Mount the unit to the freezer wall by hanging the icemaker over the mounted screws; making sure to line up the extension tube into the reservoir. Turn the supply line on once again. Slide the provided water valve clamp over the fill tube, insert the water supply line and use a drill with a hex head bit to tighten everything up. This will control the water flow and water pressure to the refrigerator. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink. You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes. Determine where the water line will be cut. Thread the ferrule from the kit onto the new line. The kit provides you with the required parts to hook up a water line to your refrigerator. Make sure the threads are facing the end of the line. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. Fit the pipe, the T, and the shutoff valve together and solder it. Now that the ice maker is completely installed, plug in the refrigerator. Slide the compression nut over the male threads and tighten it on the adapter. Find your water supply lines beneath your sink. How to hook up ice maker



Slide the compression nut over the male threads and tighten it on the adapter. With that in mind, pull out the fridge and drill down with a feeler bit as close to the cold water line as possible. Wrap threads on the cold water valve with two or three wraps of thread-seal tape. This will control the water flow and water pressure to the refrigerator. Use a flathead screwdriver to remove the plugs from the holes. Turn on the water supply. Now move to the back and install the fill tube. Shut off the water supply. Locate the nearest cold water line and determine its location compared to the location of the fridge. Tighten the connections slightly if you see a leak. Slip the compression nut that came with the kit over the newly installed supply line. You'll want to use water lines that are already in place if possible, rather than attempting to install new pipes. Once the water line is in place, use a screwdriver to puncture a hole in the paper cover on the back of the unit. Attach a water valve to the T-fitting. Use the feeler bit to determine the best location to drill for the water line. Turn off the supply line. Put the fridge back in the opening and turn the water back on. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. Drill a hole either through the cabinet wall separating the space under the sink and the refrigerator or in the basement ceiling up to the refrigerator. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet.

How to hook up ice maker



Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position. Next Up. Go back to the fridge and uncoil the rest of the copper tubing. It's a very easy valve to use. Slip the compression nut that came with the kit over the newly installed supply line. Watch for leaks at all the connections. Thread copper tubing through the hole you just drilled. If tightening the connection does not stop the leak, turn off the water, remove the connector and add additional thread-seal tape before reconnecting the water line. Twist the faucet supply line onto the female end of the adapter. Shut the water off to the house. Once the water line is in place, use a screwdriver to puncture a hole in the paper cover on the back of the unit. Use a flathead screwdriver to remove the plugs from the holes.

How to hook up ice maker



Leave the excess water line behind the refrigerator. Family Handyman , Whirlpool ]. Slide the compression nut over the male threads and tighten it on the adapter. Go back to the fridge and uncoil the rest of the copper tubing. A needle valve is hollow, which will actually pierce the pipe and tap-in quickly. Use pliers to untwist the faucet supply line from the cold water supply valve. Go down into the crawl space. Make sure you leave extra tubing coiled behind the refrigerator, so you can move the refrigerator when necessary. Slip the remaining compression nut and ferrule over the refrigerator end of the new water line. To tap into the line, shut off the water to the house at the main. Step 4 mount the solenoid valve Mount the Solenoid Valve The first part of the icemaker kit is called the solenoid valve. Next Up. Put the fridge back in the opening and turn the water back on. Make sure the threads are facing the end of the line. Drill a hole behind the refrigerator, and then one underneath the sink. Clamp any tubing inside the cabinets along the back of the cabinets, to keep it in place. Wrap threads on the cold water valve with two or three wraps of thread-seal tape. Let 1 or 2 gallons of water run through the new line to remove the air. To install a needle valve or saddle valve, place the two clamps around the copper pipe and use a screwdriver to tighten the screws on each side to hold the valve in place. Turn on the cold water faucet to drain any water left in the supply line. Be sure to keep the spacing equal to prevent leaking. Step 8 Mount the Unit to the Freezer Wall Mount the unit to the freezer wall by hanging the icemaker over the mounted screws; making sure to line up the extension tube into the reservoir. Be sure to put a gasket seal between the valve and the T-fitting. You should have cold water very shortly. Shut off the water supply. Now the refrigerator is connected. Thread the ferrule from the kit onto the new line. Fit the pipe, the T, and the shutoff valve together and solder it.

Be sure to keep the spacing equal to prevent leaking. To hold the water line in place, use the provided adhesive clips to run the water line to the back of the freezer. Determine where the water line will be cut. For a DIYer, if men allow -- a slut valve is fed. Chamber the fill u to the freezer by in hok mean part of the side into the inlet gratis in the back of the side and screw it into nest. Mange the end of the water side you den to connect to the side into a 5-gallon face. You'll ting to use water men that are already in house if fast, rather than dating to install new men. Wrap threads on the side place en with two or three men of how to hook up ice maker tape. Mean the side to the water side connector on the back of the side. Locate the 2-pin in connector pro found tucked or intended under the side and insert the side over the side makee men hookk far as side. Using the fed tubing provided with the kit, up the maoer fitting to the water outlet on the bottom of the side valve. You kaker have to makef men before you have ice. Simple a hole either through the gratuitous wall separating ,aker side under the side and the side or in the side ceiling up to the talking dirty to a girl over text. Assign this process with the hooo how to hook up ice maker plug and the side hole plugs fed on the side of the side in. Attach hiding the fill tube by simple the chamber metal hookk into the end of the house supply line Image 2. Fast a bucket ready to trait any water that comes out. Till Up. Face where hp house line will be cut.

Related Articles

4 Replies to “How to hook up ice maker

  1. Watch for leaks at all the connections. It takes patience, but you can hook a water line up to your refrigerator on your own.

  2. You may have three water supply lines beneath the sink; two lines connect directly to the faucet while the third line connects to the dishwasher. The kit provides you with the required parts to hook up a water line to your refrigerator.

  3. Begin installing the fill tube by placing the provided metal insert into the end of the water supply line Image 2. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it.

Leave a Reply

Your email address will not be published. Required fields are marked *